How to Lay Weed Mat: A Step-by-Step Guide
Laying weed mat (sometimes written weedmat) is a job most people can finish in an afternoon. The result depends mostly on the preparation: a clear, level surface and well-pinned edges matter more than the mat itself. This guide covers laying down weed mat in seven steps, from clearing the ground to trimming the edges.
Not sure how much you need? Use our weed mat calculator to work out the roll size for your area first.
What you need
- Weed mat, cut from a roll to suit your area
- Sharp scissors or a utility knife
- Landscape pegs or ground staples (one every 50 cm along the edges and seams is a common spacing)
- A rake, a spade and a tape measure
- Gloves
Step 1: Measure the area and choose a roll
Measure the length and width of the space in metres and multiply them to get the area in square metres. Add some extra for overlaps and trimming. For an L-shape or several beds, measure each rectangle separately and add them together. Then pick a roll width that suits the layout. A wider roll means fewer seams, and a narrower roll is easier to handle along paths and borders.
You can compare the sizes we stock in our weed mat rolls collection.
Step 2: Clear the ground
Remove existing weeds, grass, rocks, sticks and debris. Pull weeds out by the root where you can, because anything left behind may keep growing under the mat. If the area is very overgrown, cut the growth low first, then dig out the roots.
Step 3: Level and smooth the surface
Rake the soil so it is even, filling hollows and breaking up lumps. A smooth surface lets the mat lie flat. Raised sharp objects can snag it, so take out anything that sticks up. If you are edging a garden bed, set the edging in place now so you can tuck the mat against it.
Step 4: Roll out the mat
Unroll the weed mat across the area. Lay it flat and let it relax for a few minutes if it has been tightly rolled. Cut it a little longer than you need, then trim it to fit once it is in position. Work from one side to the other so the pieces stay straight.
Step 5: Overlap the seams
When you need more than one piece, overlap the edges so no soil shows between them. An overlap of about 10 to 15 cm is a common rule of thumb. Check the instructions that come with your product, as these can vary. Overlap where the strips meet, and place the upper edge so it faces away from the direction you will walk.
Step 6: Pin it down
Secure the mat with pegs or ground staples along the edges, through the overlaps and at the corners. Add a few across the middle of larger sheets. Pushing the pegs in until they sit flush keeps the mat from lifting in wind and from catching your feet.
Step 7: Plant through the mat and trim the edges
If you are planting through the mat, cut a small cross or X where each plant will go, fold the flaps back, dig the hole and plant. Press the flaps back around the stem so the soil is covered. Keep the hole as small as the plant allows, because gaps are where weeds are most likely to appear.
Finally, trim any excess along the edges so the mat sits neatly against your edging or border. Follow the care and finishing advice that comes with your product.
Common mistakes to avoid
- Skipping the weeding. Roots left in the soil can push up through the mat.
- Gaps between pieces. Always overlap the seams rather than butting the edges together.
- Too few pegs. Loose edges lift, fray and let weeds in.
- Oversized planting holes. Cut only what each plant needs.
- Ordering the wrong amount. Measure first, allow for overlaps and check the roll width against your layout.
Frequently asked questions
Which side of weed mat goes up?
Check the instructions that come with your product. If nothing says otherwise, lay it flat and make sure the whole surface is in contact with the soil.
Do I need to remove the grass before laying weed mat?
Yes. Clear the grass and weeds, and remove as much of the root as you can, before you lay the mat.
How much should the pieces overlap?
About 10 to 15 cm is a common guide. Follow your product's instructions where they give a figure.
How do I plant through weed mat?
Cut a small X where the plant will go, fold back the flaps, dig your hole, plant, and press the flaps back around the stem.
How do I work out how much I need?
Multiply the length by the width of your area, add an allowance for overlaps and trimming, and compare the result with the coverage of each roll. Our weed mat calculator does this for you.
Ready to start?
Once you know your area, browse our weed mat rolls and choose the width and length that fit your space.
